Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 16 Next »

Installation and Setup

To install in Arduino (required for initial install only):

  1. Download Arduino (NOT 2.x, This latest version has not yet been confirmed to work with Gumband HDK)

  2. Open Arduino

  3. Navigate to File > Preferences (or Arduino > Preferences on MacOS)

  4. Under Additional Boards Manager URLs add https://bitbucket.org/deeplocal/gumband_arduino_public/raw/main/package_gumband_index.json

  5. Navigate to Tools > Boards > Boards Manager

  6. Find and install package “Gumband Hardware”

    Image of the board manager

  7. Under Tools > Boards you should now see "Gumband Boards", where you can select “Gumband Hardware”

    Image of Gumband Hardware selected in the boards menu

Programming the Hardware

 Each hardware device runs 2 programs: 

  • The main Gumband Core 

  • The user code (your Arduino sketch)

  1. To update or install the Gumband Core select the "M0p" core from the boards menu and flash the device with a blank sketch (or any sketch)

    1. Note: This only needs to happen once, either with new blank hardware or to update to the latest Gumband version

  2. To upload your sketch select the "M4 (user code)" core from the boards menu and flash the device.

    1. Under File > Examples > Basics are some examples of how to use the device hardware like blinking the on-board LED and using the user button.

    2. Under File > Examples > Gumband API are some examples of using the Gumband API to create properties (hardware endpoints).

Having trouble programming?

To manually enter the bootloader, reboot the device while holding the user button (useful if the upload fails or a sketch bricks the device). A reboot can be achieved by manually power cycling or pressing the reset button.

Configuring the Hardware

Talking to the Device

New devices need to be configured for the Gumband SDK. This can be done over the USB serial interface.

  1. Connect the hardware to your machine using a USB cable and select it in the Tools > Port menu. It should appear as a USB COM Port (standard COM Port drivers should be sufficient for this).

  2. Open the Serial Monitor in the Arduino IDE (or your serial terminal of choice)

  3. Type then send read ip to verify connectivity

    1. An unconnected or unassigned device should respond 0.0.0.0:0.

You can send help to see a full list of commands, or see Serial Configuration Interface | Commands

Creating Credentials

To create credentials for the new device, you’ll need to login to app.gumband.com. Follow the steps outlined here or in Hardware UI | Create new Hardware

  1. Navigate to Sites > [Project Site] > Hardware > Create Hardware.

2. Create a descriptive name (this is visible to everyone in the organization so include your name or initials or project name as applicable, for example “Thomas Test” or instead of simply “Test”).

The software will automatically generate a unique hardware ID and authentication token to use on the hardware. Copy this token to your clipboard; you’ll need it in a second to finish configuring the hardware.

If you lose this authentication token, you can create a new one anytime from the ‘Auth’ tab on the Gumband dashboard.

Configure the hardware using the following commands:

Description

Command

Set Hardware ID

write hardware_id <ID>

Set Authentication Token

write auth_token <TOKEN>

Set Cloud Server

write cloud_server stag.gbtt.gumband.com:1883

Enable Cloud Server

write cloud_enable true

Reboot the device

restart

 

Once your hardware device is plugged into the network via Ethernet cable, it should be online and should appear as connected on the online console in addition to your device’s LED pulsating cyan.

See Gumband LED Status for a list of all status LED colors.

Tips for Use

  • Gumband only checks for callbacks once at the end of every iteration of the loop() function. In general, it's a bad idea to use delays within this loop() function because it inhibits the system from checking callbacks constantly.

  • When reading data from a callback function, you need to cast the incoming data to get it in a usable form. This allows you to more easily use the data more than once if necessary. The type you cast it to should match the type of data of the peripheral.

    • Ex: Use int32_t* dat = (int32_t*)data for the gmbnd_int32 type

  • Peripheral/Property names can only be 15 characters, anything longer will be truncated.

  • The on-board LED and button work with digitalWrite() functions using the LED_BUILTIN and BUTTON_BUILTIN pin assignments. However, you can also use the custom gumbandLed() On/Off/Toggle/SetBrightness and gumbandButtonPressed() functions within the Gumband API.

  • The on-board button does not need to be initialized with pinMode(); it will work automatically. It will not work properly if reconfigured to INPUT_PULLUP or INPUT_PULLDOWN.

  • Initializing pins with pinMode() is not necessary for most I/O. They will be initialized automatically when calling digital/analog read/write. To configure pullup/pulldown resistors, pinMode() is necessary, however.

Command Line Utilities

The Arduino package include an upload utility that communicates with the bootloader and can be executed directly from the command line. The gumband_loader tool is located in tools>gumband_utils directory of the installed package (typically AppData\Local\Arduino15\packages\gumband_arduino for pre 2.0 Arduino IDE under Windows).

The syntax for this tool is as follows: gumband_loader <file> <port>

where:
<file> is any valid *.gbm0 or *.gbm4 file (M0 or M4 application images)
<port> is the COM port that the hardware is connected to.

  • No labels